STM100C : Site transformer
10kVA Single phase site transformer
230V to 6 x 110V (16 and 32 amp outlets)
| Price for 1+: | £400.40 each. |
| Price for 5+: | £380.80 each. |
| Weight: | 73.00 kg. |
| VA: | 10,000 VA. |
- The 110V transformer is for use on building sites to provide a reduced voltage.
- 40 amp input screw terminal block
- 4 x 16 amp outlet sockets
- 2 x 32 amp outlet sockets
- CTE (Centre tap to earth)
- Fitted with 5 MCBs (Miniature circuit breakers)
- One MCB on the input, two on the 16 amp outlets & one on each 32 amp outlet
- Constructed with a robust heavy duty site case and housed under a weatherproof cover.
- Climatic class outdoor use
- Manufactured to BSEN61558 & BS4343
- British Built
- Delivery within 48 hours
| Intermittent or tool rating: | Single phase 10,000VA @ 50/60HZ |
| Continuous rating: | 10,000VA |
| Input: | 230V @ 43.48 amps |
| Output: | 4 x 110V CTE with IP44 16 amp panel mounting sockets with weatherproof covers |
| Output: | 2 x 110V CTE @ 90.91 amps with IP44 32 amp panel mounting sockets with weatherproof covers |
| Input protection: | 1 x 40 amp 2 pole type D MCB |
| Output protection: | 2 x 16 amp 2 pole type C MCB + 2 x 32 amp 2 pole type C MCB |
| Tripping Characteristics: | European standard EN60898 (-25 deg C - +55 deg C) |
| Earthing: | Earth sreen between primary & secondary windings |
| Insulation: | Thermal insulation Class E. Maximum 120 deg C |
| Temperture rise: | 75 deg C. Maximum 80 deg C |
| Feeder Cable Size: | Up to 30m 6mm or 60m 10mm |
| Enclosure: | Sheet steel ventilation drip proof IP40 + IP44 Weatherproof covers over MCBs |
| Dimensions: | H 590mm (inc. handles 640mm) x W 365mm(inc. handles 430mm) x D 440mm |
| Weight: | 73Kg |
Before using this equipment and to avoid personal injury, carefully read and understand these instructions. If there is anything you do not understand. DO NOT use this equipment, seek advise.
Make sur you are aware of all safety requirements and that this equipment is suitable for the task you wish to undertake.
The work area must be cordoned off from the general public and bystanders.
Persons who are under the influence of alcohol or drugs must not operate this equipment.
You must perform a risk assessment before using this equipment to ensure your safety and the safety of others.
Wear the correct personal protective equipment for the task ahead.
Do not wear loose jewellery or clothing that may get in the way of your work.
Inform everyone in the area of what you are doing.
This equipment may weigh in excess of 25 kilos, if so, do not lift it by yourself, GET HELP.
Ensure adequate ventilation when using this equipment. Do not operate the unit close to flammable or explosive materials.
Do not lift or remove the unit by its power supply cable.
Always switch OFF the unit when cleaning, making adjustments or when left unattended.
Transport, store and operate this equipment in an upright position.
Carefully inspect the equipment before use, if there is any doubt about its condition, DON'T USE IT. Check specifically for damage to casing, power sockets and leads.
HEAT DAMAGE RISK
Never place a portable transformer on any surface, which may be damaged by heat. Regardless of size or type, all portable transformers work at high temperatures. These temperatures are sufficient to melt linoleum and synthetic carpet. Severe damage will also be caused to wood and similar materials.
Heat produced by the transformer is increased if the transformer is operated at its intermittent (max) rating.
Only place the transformer on a surface you know, is heat resistant.
ELECTRICAL SAFETY
Portable transformers require a standard 230v 13amp power supply.
If the equipment fails, or if any part becomes damaged, return it. DO NOT repair it yourself.
Do not plug the transformer into an extension lead, only use extension leads from the transformer.
Fully unwind and loosely coil all extension leads. Position them away from the equipment where they will be protected from water, sharp objects and where they will not pose a trip hazard.
Keep the equipment dry; protect this equipment from damp or wet conditions.
For additional safety always use an RCD between the transformer and the item being powered.
Switch the power OFF before plugging into the supply.
*WARRANTY
All our transformers are maunfactured using the finest materials and are subject to stringent testing before leaving the factory. If there is a manufacturing fault in a site transformer bought from us, we will refund you the purchace price. You simply need to return the transformer to us (see contact page for address) with the original receipt and after we assess the fault, assuming it is a manufactuing fault, we will credit you the cost of the item.
